# This will be the name of the output files
name: xwafer
wafers: ["X"]

# round or square wafer
shape: square

# diameter/edge size of the wafer
size: 310

# large or small markers and labels
marker_size: small
font_size: small

# origin settings.  x_origin can be left, right, or center.  y_origin can
# be top, bottom, or center.  Using right or top implies that the X/Y values
# for that axis are negative, or else we'll be drawing outside the image.
x_origin: left
y_origin: bottom

# sensor X and Y values, in mm relative to the origin
X: [ 3.00, 3.00, 3.00, 3.00, 3.00, 3.00, 3.00, 3.00, 3.00, 3.00, 3.00, 3.00,
    13.00, 23.00, 46.43, 89.86, 133.29, 176.72, 220.15, 263.58, 287.01, 297.01,
    307.01, 307.01, 307.01, 307.01, 307.01, 307.01, 307.01, 307.01, 307.01,
    307.01, 307.01, 307.01, 297.01, 287.01, 263.58, 220.15, 176.72, 133.29,
    89.86, 46.43, 23.00, 13.00, 46.43, 46.43, 46.43, 46.43, 46.43, 46.43,
    89.86, 133.29, 176.72, 220.15, 263.58, 263.58, 263.58, 263.58, 263.58,
    263.58, 220.15, 176.72, 133.29, 89.86, 89.86, 89.86, 89.86, 89.86,
    133.29, 176.72, 220.15, 220.15, 220.15, 220.15, 176.72, 133.29, 133.29,
    133.29, 176.72, 176.72]
Y: [ 3.00, 13.07, 23.07, 46.50, 89.93, 133.36, 176.79, 220.22, 263.65, 287.08,
    297.08, 307.08, 307.08, 307.08, 307.08, 307.08, 307.08, 307.08, 307.08,
    307.08, 307.08, 307.08, 307.08, 297.08, 287.08, 263.65, 220.22, 176.79,
    133.36, 89.93, 46.50, 23.07, 13.07, 3.00, 3.00, 3.00, 3.00, 3.00, 3.00,
    3.00, 3.00, 3.00, 3.00, 3.00, 46.50, 89.93, 133.36, 176.79, 220.22, 263.65,
    263.65, 263.65, 263.65, 263.65, 263.65, 220.22, 176.79, 133.36, 89.93,
    46.50, 46.50, 46.50, 46.50, 46.50, 89.93, 133.36, 176.79, 220.22, 220.22,
    220.22, 220.22, 176.79, 133.36, 89.93, 89.93, 89.93, 133.36, 176.79,
    176.79, 133.36 ]

# set this to either 0 or 1 for the initial sensor number (usually 1)
start_sn: 1

# Normally, positive X is to the right, and positive Y is up.
# These settings can be used to reverse one or both of these.
reverse_x: false
reverse_y: false

# these are sensors whose labels need to be repositioned.  Sensor numbers
# start at start_sn.  Directions are up, down, left, and right, and values
# are multiples of the marker size.
label_exceptions: {
    21: { left: [0, 0] },
    22: { left: [0, 0] },
    23: { left: [0, 0] },
    24: { left: [0, 0] },
    25: { left: [0, 0] },
    26: { left: [0, 0] },
    27: { left: [0, 0] },
    28: { left: [0, 0] },
    29: { left: [0, 0] },
    30: { left: [0, 0] },
    31: { left: [0, 0] },
    32: { left: [0, 0] },
    33: { left: [0, 0] },
    34: { left: [0, 0] },
    35: { left: [0, 0] },
    36: { left: [0, 0] }
}